坤坤跳舞"的单片机代码

一纸桥书~9-1LED点阵屏显示动画.rar 23.44KB

资源介绍:

这是一个用keil5软件编写的单片机代码，其中包含了用LED点阵屏和定时器实现，通过取模器生成动画的每个动作，然后通过定时器控制动作的播放，完成该项目的前提是先储备好LED点阵屏和定时器的基础知识，还有51单片机的相对应的原理图中的接口，还有利用51单片机烧录代码的前提是将外部晶振GND和OE两个引脚连接起来才可以实现点阵屏的开启，以上是这个项目的基本使用方法，同时也可以继续在此项目添加蜂鸣器的运用，使得本项目同时有坤坤的动画和坤坤的music，小黑子们加油吧，基你太美。。。。

#include <REGX52> #include "Delay.h" #include "MatrixLED.h" //动画数组 unsigned char code image[]={ 0x00,0x0E,0x1B,0x7F,0X7F,0X1B,0X0E,0X00, 0X00,0X04,0X0C,0X18,0X7F,0X7F,0X1B,0X0E, 0X00,0X08,0X0C,0X05,0X7F,0X7F,0X1E,0X0C, 0XC0,0X00,0X41,0X22,0X1A,0X7C,0X7D,0X1A, 0X00,0X60,0X61,0X12,0X0A,0X7E,0X7F,0X08, 0X00,0X06,0X0E,0X08,0X0B,0X3E,0X3E,0X0B, 0X00,0X03,0X0B,0X08,0X0B,0X3E,0X3E,0X0B, 0X00,0X06,0X0E,0X08,0X09,0X3F,0X3E,0X0B, 0X00,0X0E,0X13,0X7E,0X7E,0X1F,0X0E,0X00, 0X08,0X13,0X7E,0X7E,0X12,0X1D,0X0C,0X00, 0X09,0X12,0X7E,0X7F,0X10,0X13,0X03,0X00, 0X09,0X12,0X7E,0X7F,0X10,0X1C,0X0C,0X00, 0X00,0X0C,0X15,0X7E,0X7E,0X17,0X0E,0X00, 0X00,0X30,0X38,0X0D,0X7E,0X7F,0X1D,0X08, 0XC0,0XC0,0X30,0X1B,0X7C,0X7F,0X08,0X00, 0X00,0X00,0X37,0XF8,0XFA,0X34,0X00,0X00, 0X00,0X00,0X1B,0X7C,0X7C,0X1A,0X01,0X00, 0X00,0X00,0X09,0X1E,0X7C,0X7F,0X18,0X00, 0X00,0X00,0X1B,0X7C,0X7C,0X1B,0X00,0X00, 0X00,0X00,0X09,0X1E,0X7C,0X7F,0X18,0X00, 0X00,0X00,0X1B,0X7C,0X7C,0X1B,0X00,0X00, 0X08,0X10,0X16,0X7C,0X7F,0X10,0X08,0X00, 0X00,0X10,0X13,0X7C,0X7E,0X18,0X00,0X00, 0X00,0X08,0X13,0X7C,0X7F,0X10,0X10,0X00, 0X00,0X08,0X12,0XFC,0XFD,0X3A,0X00,0X00, 0X00,0X08,0X12,0XFC,0XFC,0X22,0X10,0X00, 0X00,0X00,0X61,0X12,0X7C,0X7F,0X10,0X60, 0X00,0X00,0X20,0X11,0X12,0X7C,0X7E,0X19, 0X00,0X00,0X00,0X31,0X0A,0X7C,0X7E,0X0D, 0X00,0X00,0X20,0X11,0X12,0X7C,0X7E,0X19, 0X00,0X00,0X00,0X31,0X0A,0X7C,0X7E,0X0D, 0X00,0X00,0X20,0X11,0X12,0X7C,0X7E,0X19, 0X00,0X00,0X00,0X31,0X0A,0X7C,0X7E,0X0D, 0X00,0X00,0X20,0X11,0X12,0X7C,0X7E,0X19, 0X00,0X00,0X00,0X31,0X0A,0X7C,0X7E,0X0D }; void main() { MatrixLed_Init();//初始化 while(1) { unsigned char i,k,offset; for(k=0;k<15;k++)//帧延时 { for(i=0;i<8;i++) { MatrixLED_ShowColumn(i,image[i+offset]);//显示动画 } } offset+=8; if(offset==280)offset=0; } }